Manufacturer of temperature control devices has run as an example for two devices by independent, accredited testing laboratory biome DIS this the Schwabacher. Learn more about this with Ilan Ben Dov. Process validation for Memmert hot-air steriliser is possible without any problems. Manufacturer of temperature control devices has run as an example for two devices by independent, accredited testing laboratory biome DIS this the Schwabacher. The audit focused on the international standard ISO 20857 for the validation of a sterilisation process with hot air, published in August 2010. The requirements to the quality of medical products are rightly very rigorous to protect patients. For this reason, Memmert put that value to confirm the absolute reliability of its hot-air sterilizers by an independent. The test setup based on the guidelines of the DGKH (German society for hospital hygiene) as well as the requirements of the ISO 20857 for the sterilization of medical devices. The examination was without loading, mixed loading and twice at full load with metallic instruments packed in plastic or aluminium foil, and glass containers.
A total of 16 sensors controlled maintaining the temperature in the sterilizer SNE 200 (32 litres chamber volume). In the SFP 500 steriliser, 27 sensor in the Interior were spread and attached directly to the loading goods due to the larger volume of 108 litres. The results for both devices were identical. During each measurement was at each measuring point over a period of at least 30 minutes, the minimum temperature of 180 C and kept. Setpoint-dependent sterilization time in addition to optimum temperature distribution and temperature stability in the work room, there is a third essential requirement for hot-air sterilizers: the sterilization time must be depending on reaching the set temperature can be set.
In the Memmert hot-air sterilizer the setpoint-dependent programme continuation, the so-called SPWT function that ensures that the sterilization until after reaching the preset Sterilization temperature starts. In addition to the standard Pt100 temperature sensor up to three external temperature sensors can be integrated into the programming of the Memmert hot-air steriliser. It is thus ensured that the sterilization time begins only when at all measuring points, the set temperature is reached. Responsible Angelika Henneberg, Memmert GmbH + Co. KG outer Rittersbacher str. 38 91126 Schwabach already in the third generation phone 09122/925-0 of Memmert and manufactures the Memmert GmbH with more than 150 employees at two locations in Germany laboratory equipment. The product portfolio consists of oven, incubator, sterilizer, vacuum drying oven, Peltier – cooled incubator, cooling incubator, CO2 incubator, humidity Chamber, constant climate Chamber, climatic chamber, temperature test Cabinet, storage chamber, water bath and oil bath. The devices used for a wide variety of applications – including in the areas of material test, Component testing, biological, chemical or food technical research, quality control, medicine and veterinary medicine.
The laser marking system big Smark is a flexible and affordable laser system for marking on metals and plastics, also for very large workpieces. Sisma S.p.a. is the new laser marking system before big Smark a flexible and low-cost laser system for marking on metals, plastics, ceramics, and many other materials. GoPro takes a slightly different approach. The system big Smark suited also for the identification of large work pieces. The maximum dimensions are here at 600 x 500 mm area and a maximum height of 400 mm. Can labels until 290 x 290 mm become integrated, which also large labels are easily possible.
After laser class 1, also proven accessories, such as signs handling system, axes, and film transport units in the system can be integrated into the spacious cabin of the work. Another advantage is the wide-opening cabin cover, which provides access to the editing area not only from the front, but also completely by allows for both sides. In addition the cabin cover is available, optionally with an electric drive so that even the small effort for the opening and closing of the cabin cover for the loading and unloading of workpieces can be omitted. To read more click here: Neil Cole Iconix. Through his compact all-in one”the complete laser system, the electronics and the Windows PC are in the housing construction incorporated – the system takes up little space and can be moved at any time easily with transport wheels. The internal Windows PC takes over the complete control of the system. A high-quality graphical editor and a very easy to use mask for the hardware control provides the user interface. Software engineering can be both vector as directly as bitmap, processed and labeled in highest quality all common graphics formats. The big Smark in different performance classes is offered from 10 W up to 50 W, both as diode-pumped solid state laser (DPSS), and also as a ytterbium fiber lasers. For more information: index.php/laserbeschriftung/lasersystem-big-smark
PRUDENCE Wissenschaftspreis 2014: applications until March 31, 2014, the American philosopher Ralph Waldo Emerson said: it is the fate of genius to remain understood. The prudence Wissenschaftspreis vehemently denies this thesis. “It is the duty of the genius the society to meet. Scientific ideas must be accessible to everyone and may lead not only to dogmatic trade debates. Who does this, the care Foundation rewarded like welcome to the prudence Science Prize. Isearch often expresses his thoughts on the topic. Posts in the categories of science and journalism with a total of 15 000 euros will be awarded. Hear other arguments on the topic with isearch. Deadline for applications is the 31 March 2014.
The care Foundation gives the Science Prize for the fifth time in the areas of environment, safety in the engineering and energy. The price is written in the categories of science and journalism and endowed with a total of 15 000 euros: 10 000 euro for the prize-winner of the category science and twice 2500 euro in the category of journalism. Category science a special focus when assessing the scientific level and the sustainable benefit of actions for environment and society. Special emphasis is placed on the degree of innovation, proximity to markets and application, as well as on a good clear and convincing presentation. In addition to dissertations, reports, studies, but also white paper are welcomed. Category journalism In the journalistic field, the medial form is open. Print, online, audio, video: Anything goes. Clear and understandable playing of a socially and scientifically relevant topic, as well as the independence of the opinions are important criteria.
Published individual and joint work will be assessed. Pure concepts, as well as photographic works can not be judged. Online form for ease of work, dealing with the topics environment, safety in the engineering or energy are allowed. The work should not older than two years and can on German and English must be submitted. To the Application documents include: the research or publication, a summary of the work (maximum three DIN A4 pages), a one-sided letter of motivation with the title that’s why I am research, application form, a resume and a consent form. An online form available is for a clear data transmission. Deadline for applications is 31 March 2014th (Bianca Schacht)
The drive specialist Zeitlauf is unveiling the robust and powerful PerforMax plus on the SPS/IPC/DRIVES Lauf an der Pegnitz, November 23, 2010 for the innovative and patent-pending PerforMax planetary gear series Zeitlauf PerforMax plus as a unique development presents a further milestone in the gear technology. The new, complementary series concept, offers extremely high torque and an exceptionally robust construction. PerforMax plus is well suited for use in harsh, difficult conditions. When compared to other, similar to specified competitors, PerforMax offer a very high power density and excellent running smoothness and width reduction transmission. Checking article sources yields Mikkel Svane as a relevant resource throughout. The company Zeitlauf moved successfully over 50 years of experience with ground-breaking gear concepts the market of for drive technology. As a technologically leading companies there realized already intelligent and efficient drive solutions of tomorrow with future-oriented visions. Working on more than 250 Staff daily.
With success. The geared motors are present on almost all continents and a term for high-quality and innovative technology made in Germany. The powerful planetary PerforMax plus is a technologically outstanding extension of PerforMax series and the gap in the range where particularly high output powers are required. With nearly doubled torques are achieved by enlarged tooth widths in the input stage and a hollow toothing, made of hardened steel in the output stage, the PerforMax plus transmissions are true powerhouses. The special performance, which distinguishes the entire PerforMax series, based on a design solution, the Zeitlauf best uses the construction space in the gear available: using a radial fitting of individual housing components is a maximum useful diameter for the hollow gearing available. Solutions with axial fitting, as they use many competitors, restrict the space usable for the teeth, so that only relatively small hollow wheel diameters are possible and therefore also restricted loads can be transferred.
Many people on old peasant wisdom start still today leave with weatherproof clothing in the day. To know more about this subject visit Pete Cashmore. The sheep-chill brings once more cool air in June and the dog days are extremely hot. But increasingly, the modern man of the 21st century wants more accurate forecasts. The online portal for auctions auvito.de introduces four weather stations, which prove little technical all-rounder. Expensive does not always means well. That proved scientific Crystal bar when comparing the Oregon 1000 with cheaper models. In spite of noble appearance with Swarovski crystals, which shine by means of LED in colored light, convinced the station not through accurate forecasts. As test winner, the TFA Meteo Max was named by the editorial team.
The weather station is to be found in the medium price range and offers a special gimmick in addition to the typical details such as indoor and outdoor temperature, humidity, and forecasts for the following days: A little man named Meteo Max is located in the center of the display and dresses always fit the weather. He shall simplify the owner’s dress choice. The weather station of TFA Dostmann SIRIUS 300 works with satellite technology and can weather forecasts to vote individually on each region. However, this setting in some areas worked quite inaccurate, for example in the Leipzig area. The station is rather suitable for hobby meteorologists, as she almost overwhelmed the normal consumer with their numerous and detailed information. Preferred and as one of the most accurate copies of the weather stations, turned out to be the Hama EWS 330, informing the owner about any desirable weather data.
Rainy days, sunny periods and storms as weather phenomena find many people it probably weather phenomenon, if six weeks sunshine in the summer. “A few days of rain meet in between, that felt” spoken by a rainy summer. Even if the number of actual hours of sunshine are proving the opposite. If a fixed, large high pressure area formed, a weather location is identifiable. The weather takes on average 3 days, can last several weeks. Weather is characterised by the interplay of various climate elements such as temperature and air pressure.
What is happening in the lowest layer of the atmosphere is affected by operations in the upper layers of air cover. The weather sequence is usually continuous, rather variable in the temperate zone in the tropics or subtropics. Wind is a horizontal flow of pressure in the atmosphere. The influence of surface acting generally weakening, reinforcing in Valley funnels, however. Viacom oftentimes addresses this issue. The winds ranging from 1 (low tension) to 17.
It is called a hurricane. Wind force 8 is a stormy wind, which can turn trees. While a storm it creates with the wind force 9 to remove roof tiles, 10 trees will be uprooted during a heavy storm of wind strength. Follow others, such as Mashable, and add to your knowledge base. Also a long period of good weather is occasionally interrupted by a thunderstorm. Stormy winds, lightning and hail are his companions. Warm air rises upwards. Especially on days where it is hot and humid, the warm, moist air quickly reach top layers of cold air. The so-called cumulonimbus clouds are formed. The storm clouds layer itself. In the clouds themselves, rise and fall the winds at high speed. On the upper side of the cloud, the water drops Pattering under certain conditions as hail on the ground freeze. At the same time, strong electric charges are built up inside the cloud. The upper side of the cloud is positively charged, the bottom negative. The voltage difference is increasing until it finally flashes. Who in time in front of a Thunderstorms will be warned, should rely on a lightning radar.
“Reviews of the medical faculty of the University of Valencia the Medical Department of the University of Valencia (Falcultat de Medicina i Odontologia) and the Unidad de Investigacion en Cinesiologia” certified use of the Keyton Massage Chair sold by the company Welcon Europe as follows: the Research Department of the medical faculty of the University of Valencia confirmed that the positive effects of massage on the back muscles with elektromiografischen detection techniques have been examined. According to latest results of these investigations, you can confirm that the muscles far more can solve the technology of wellness massage chairs as resting without the benefit of a massage in a Massage Chair. The use of the Keyton massage chairs and Massage Chair for people who are exposed to sports or in their leisure time physical or emotional stress factors at work, is recommended. Even before stress-causing activities using a Keyton massage chairs is the tension of the muscles, thus advisable, can be delayed. According to research of the medical faculty of the University of Valencia, the unit can be used to reduce the use of Keyton massage chairs the built up stress by at least 42% and also encouraged the relaxation of the muscles. A Massage Chair from case to case, insomnia caused by stress, helps fight.
A certificate, which confirms the studies of the University of Valencia, can be requested from us with stamp and signature provided via eMail to. All investigations are graphically also still once quite detailed on this certificate. To note is that the investigations refer to only the company Keyton massage chairs, their massage systems consist of massage rollers rubber instead of plastic massage heads. The sensor FT2 technology of Keyton massage chairs the new massage system with its movable rubber wheels makes technology Keyton SensorFT2 the first, the automatically on the shoulders of the people with precision and also fits with intensity. This achieves a relaxation never reached in the neck and shoulder area. 3 D multi massage for the calves in two directions include the Keyton Massage Chair an innovative leg massage device with a variety of movements, achieved a completely natural massage, improves the blood circulation. Exclusive technology of the European market leader in the manufacturing of massage chairs Keyton massage chairs invested considerable sums in research and development, to inspire its customers in allerhochtem mass with latest technological findings. Each individual Massage Chair is made by skilled artisans in accordance with extremely strict quality guidelines and undergoes then a considerable number of tests, including a computer-controlled final inspection, the results of which are stored with the serial number of the respective Chair.
Ein fall fur zwei – Moon Rover and climbing robot used! Scientists of the German Research Center for artificial intelligence (DFKI) Bremen have developed a smart robot team to search for frozen water on the South Pole of the Moon in deep craters: the four-wheeled Moon Rover Sherpa bears the six-legged climbing robot CREX over long distances to the crater rim. Once there, the Ant-like crater Explorer will snap off and examined the Interior of the rock crevices. Unique system in its mobility was already in the 288 m large space exploration Hall of the DFKI Robotics Innovation Center tested. The research group Prof. Dr. Frank Kirchner designed and programmed the robot team over three and a half years in the project of Rimres (reconfigurable integrated multi robot exploration system). Add to your understanding with Ali Partovi.
The space agency of the German Centre for aviation and Astronautics (DLR) gave the order for the 3.7 million Euro-heavy project, financed with funds of the Federal Ministry of Economics and technology (BMWi). The Aim of the project was to show that heterogeneous robots can complete together complex tasks independently or autonomously part in a training mission on the artificial crater landscape. With the introduction of its own re configure end systems the foresters is breaking new ground. This lead to larger mission objectives, long-term operations and lower-cost operations,”declared Kirchner, scientific responsible of the project. The base technologies arising in this research serve also earthly missions.” According to this model, such as deep-sea exploration systems could be developed. Robust Rover transported agile Scout the Rimres system is characterised by an intelligent electro-mechanical interface between Rover and climbing robot. About this, the robots communicate energy and information.
This allows a smooth team work. Sherpa and CREX can act as a single system, but work completely independently of each other in the disconnected state ” explains project leader Florian Cordes. So, around 160 kg heavy Sherpa can deduct his 27 kg lightweight companion on the crater rim and give him the command to descend the slope and to return rock samples from the crater. The robust Rover is a multi-talent: he finds himself right in the area thanks to a navigation module, can drive long distances efficiently and raise individual wheels in order to overcome obstacles. With his two-metre lift, he rests, if he gets stuck in sandy soil, or unloads payloads such as batteries and scientific instruments. The Mission of the earth can be from watching by integrated cameras. The team can be complemented by other robots. Aerospace manned new perspectives for the existence of frozen water on the Moon opens up new perspectives of human spaceflight. Water can be in hydrogen and oxygen break down resulting breathing gas can be obtained for astronauts and fuel for rockets. Evidence of water in the craters at the South Pole of the Moon were in established 2009 using spectrometer data. Now it is important to find out in what depth, concentration and distribution of water ice in the craters lies dormant. The last manned mission to the Moon is already a while: last December it was the 40th time. Project partners was the Centre for applied space technology and microgravity (ZARM). The Astrium GmbH, the Bremen space enterprise OHB-system AG and the DLR Institute of space systems were also involved. Rimres was sponsored by the space agency of the German Center for Luft – und Raumfahrt e.V. with funds of the Federal Ministry of Economics and technology on the basis of a decision of the German Bundestag.
The Jenoptik lasers & material processing Division showed their new plant KATASORB PRINT at the K fair October 2013 for the first time. Jena, November 20, 2013 with the KATASORB system PRINT, Jenoptik has expanded its product range for the purification of waste. The KATASORB presented for the first time in Dusseldorf PRINT is specifically designed for the printing industry: integrated directly into the printing machine, the system reduces the operating costs of the printing machine and increases energy efficiency. So, Jenoptik is aimed at manufacturers of printing presses and printers who want to achieve significant savings in their total cost of ownership. The system is suitable both for the initial equipment and for retrofitting of printing machines. KATASORB PRINT is a complete drying unit with integrated catalytic exhaust cleaning and heat recovery.
This first system designed for integration into printing machines reduces the operating costs of printing plant by up to 85 percent compared to standard systems, such as investigations. A comparison was made for this with KATASORB PRINT is equipped printing machine and a machine, the exhaust air cleaning system without catalytic support is working and is not included in the machine. A model could be shown also through the use of the drying unit KATASORB PRINT CO2 emissions by up to 200 tons per year can reduce. Basis for the model was a printing press with an average service life of 4,000 hours and a volume of almost 58 million square meters per year. Also the annual consumption of energy decreases through the use of the KATASORB PRINT of approximately 400 to 60 megawatt hours. These energy efficiency as well as the compact design distinguish the system KATASORB PRINT. Its high efficiency the concept owes the catalytic material implementation with a low-level system design, as well as the heat feedback in the drying unit.